![how to configure 2 lan 2 wan asa 5505 cisco how to configure 2 lan 2 wan asa 5505 cisco](https://oasysadmin.files.wordpress.com/2013/06/asadualispnew.png)
- #How to configure 2 lan 2 wan asa 5505 cisco how to#
- #How to configure 2 lan 2 wan asa 5505 cisco update#
- #How to configure 2 lan 2 wan asa 5505 cisco password#
- #How to configure 2 lan 2 wan asa 5505 cisco plus#
I just tried to offer you a starting point for a basic configuration from where you can build your knowledge further. There are many more configuration features that you need to implement to increase the security of your network, such as Static and Dynamic NAT, Access Control Lists to control traffic flow, DMZ zones, VPN etc. The above basic configuration is just the beginning for making the appliance operational. The PAT configuration below is for ASA 8.3 and later: NAT (static and dynamic) and PAT are configured under network objects. The “global” command is no longer supported. This version introduced several important configuration changes, especially on the NAT/PAT mechanism.
#How to configure 2 lan 2 wan asa 5505 cisco update#
UPDATE for ASA Version 8.3 and later (including ASA 9.x)įrom March 2010, Cisco announced the new Cisco ASA software version 8.3.
![how to configure 2 lan 2 wan asa 5505 cisco how to configure 2 lan 2 wan asa 5505 cisco](https://packetlife.net/media/blog/attachments/614/L2L_VPN.png)
Step 4: Configure PAT on the outside interfaceĪSA5510(config)# global (outside) 1 interfaceĪSA5510(config)# nat (inside) 1 0.0.0.0 0.0.0.0
#How to configure 2 lan 2 wan asa 5505 cisco password#
Configure this under Configuration Mode:ĪSA5510(config)# enable password mysecretpassword
![how to configure 2 lan 2 wan asa 5505 cisco how to configure 2 lan 2 wan asa 5505 cisco](https://m.media-amazon.com/images/I/518zZpgDneL._AC_SY355_.jpg)
Step1: Configure a privileged level password (enable password)īy default there is no password for accessing the ASA firewall, so the first step before doing anything else is to configure a privileged level password, which will be needed to allow subsequent access to the appliance. Let’s see a snippet of the required configuration steps for this basic scenario:
![how to configure 2 lan 2 wan asa 5505 cisco how to configure 2 lan 2 wan asa 5505 cisco](https://i.ytimg.com/vi/XXkx8jBasmg/maxresdefault.jpg)
All outbound communication (from inside to outside) will be translated using Port Address Translation (PAT) on the outside public interface. Route outside 0.0.0.0 0.0.0.0 firewall will be configured to supply IP addresses dynamically (using DHCP) to the internal hosts.
#How to configure 2 lan 2 wan asa 5505 cisco how to#
How to Setup VLAN Routing on an ASA 5505 (Pre Version 8.3) Nat (PHONE_VLAN_112,outside) dynamic interfaceĪccess-group outbound in interface insideĪccess-group VLAN112_outbound in interface PHONE_VLAN_112 Same-security-traffic permit inter-interface Connect to the firewall, go to enable mode, then go to configure terminal mode. The commands you use will be different if your firewall is running an operating system earlier than 8.3, check your ASA version and proceed to the correct set of commands.įor Firewalls running an Operating System OLDER than 8.3 go here How to Setup VLAN Routing on an ASA 5505 (Version 8.3 and Newer)ġ.
#How to configure 2 lan 2 wan asa 5505 cisco plus#
Your ASA MUST have a Security Plus licence to be able to do this. Here’s the scenario I’m going to use for this example.īefore we start, yes I know the ASA is a firewall not a router! A better solution would be to have either a router behind the firewall or, (as is more common) a switch that is layer 3 capable, i.e it can route. Finally I picked out the relevant parts of the upgraded config. So I built a firewall with 8.2 code, then worked out how to do it, then upgraded the firewall to version 9.1. I did an internet search and tried to find some configs I could reverse engineer, the few I found were old (Pre version 8.3) ones and the little info I got were more people in forums asking why theirs did not work. In addition I needed to route traffic between both the internal VLANs. But this client needed a secondary VLAN setting up for IP Phones. I had to set this up for a client this week, I’ve setup a DMZ on a 5505 before and I’ve setup other VLANs to do other jobs, e.g.